TS-7180 FPGA
From embeddedTS Manuals
The TS-7180 FPGA registers are accessed over I2C. The supplied 'tshwctl' utility may be used to access these registers; run 'tshwctl -h' to see how to use it.
The FPGA is available at I2C addresses 0x28-0x2f. First write the address which is 16-bits, followed by the data which is 8-bits.
The tables below list all the registers and their functions.
| Address | Bits | Description |
|---|---|---|
| 0-43 | 7:3 | Reserved (Write 0) |
| 2 | GPIOn Input Data | |
| 1 | GPIOn Output Data | |
| 0 | GPIOn Output Enable | |
| 307 | 0 | BT/MODEM# control[1] |
| 308 | 0 | HD1/GPS# control[2] |
| 309 | 0 | PWM control[3] |
In the above table the GPIO uses are listed in the table below.
| IO Number | Pad | Direction |
|---|---|---|
| 0 | WIFI_RESET# | OUT |
| 1 | EN_WIFI_PWR | OUT |
| 2 | EN_YEL_LED# | OUT |
| 3 | EN_GREEN_LED# | OUT |
| 4 | EN_RED_LED# | OUT |
| 5 | EN_BLUE_LED# | OUT |
| 6 | EN_CL_1 | OUT |
| 7 | EN_CL_2 | OUT |
| 8 | EN_CL_3 | OUT |
| 9 | EN_CL_4 | OUT |
| 10 | EN_ADC1_10V | OUT |
| 11 | EN_ADC2_10V | OUT |
| 12 | EN_ADC3_10V | OUT |
| 13 | EN_ADC4_10V | OUT |
| 14 | EN_SD_POWER | OUT |
| 15 | EN_USB_HOST_5V | OUT |
| 16 | EN_OFF_BD_5V | OUT |
| 17 | EN_CELL_MODEM_PWR | OUT |
| 18 | EN_NIMBEL_3.3V | OUT |
| 19 | EN_GPS_PWR# | OUT |
| 20 | EN_CAN_XVR# | OUT |
| 21 | EN_232_XVR | OUT |
| 22 | EN_LS_OUT_1 | OUT |
| 23 | EN_LS_OUT_2 | OUT |
| 24 | EN_LS_OUT_3 | OUT |
| 25 | EN_LS_OUT_4 | OUT |
| 26 | EN_LS_OUT_5 | OUT |
| 27 | EN_LS_OUT_6 | OUT |
| 28 | EN_LS_OUT_7 | OUT |
| 29 | Unused | n/a |
| 30 | Unused | n/a |
| 31 | Unused | n/a |
| 32 | DIG_IN_1 | IN |
| 33 | DIG_IN_2 | IN |
| 34 | DIG_IN_3 | IN |
| 35 | DIG_IN_4 | IN |
| 36 | SD_BOOT_JMP# | IN |
| 37 | DIO_IN_1 | IN |
| 38 | DIO_IN_2 | IN |
| 39 | DIO_IN_3 | IN |
| 40 | DIO_IN_4 | IN |
| 41 | DIO_IN_5 | IN |
| 42 | DIO_IN_6 | IN |
| 43 | DIO_IN_7 | IN |