TS-7553

TS-7553

Released Mar. 2010
Documentation
Schematic
Mechanical Drawing
FTP Path

Overview

The TS-7553 was released Mar. 2010 and is a smaller form factor and cost reduced version of the TS-7552 without the extra USB ports and 8-28V switching power supply. It was designed to be mated with an inexpensive plastic enclosure and serve as a standalone general purpose embedded server.

Features

• 250Mhz Cavium ARM9 CPU core (Faraday 526)
• 64MByte 16-bit wide DDR SDRAM running at 125Mhz
• 2 USB 2.0 High speed (480 Mb/s) Host ports
• 1 USB 2.0 slave port
• 1 TTL serial console port (16550) on CPU
• Hardware watchdog on FPGA
• Optional battery backed real time clock
• 10/100 Mbit on-CPU ethernet
• Low power (TS-7500 is 395mA @ 5V or 2.0 Watt)
• Fanless/heatsink-less operation up to 80C temperatures
• Customizable FPGA opencore (with Verilog sources)
• High speed SPI and I2C interfaces
• Standard CAN controller on DB9 connector
• Standard RS485 XUART serial port on DB9
• 2 RS232 XUART serial ports on DB9
• Optional onboard 802.11bg radio
• Onboard microSD socket
• 256Mbyte onboard XNAND Drive preloaded with Debian Linux
• 12 3.3V CPU/FPGA controlled GPIOs
• Designed to fit in a low cost plastic enclosure

Optional Features/Accessories

• CB-USB-AMBM: USB Cable w/ connectors USB-A Male to USB-B Male (can also used as power supply cable)
• CB-USB-AMAF: USB Cable w/ connectors USB-A Male to USB-A Female
• CB7-05: Null modem cable with a DB9F at each end
• RC-DB9: 10-pin header COM port adapter cable to DB-9
• TS-9448: Console Mini-Peripheral Board w/ 1 RC-DB9 cable
• WIFI-G-USB: USB 802.11g wireless network interface
• PS-5VDC-1AMP: 5VDC 1AMP Power Supply (100-240V)
• TS-ENC820: Plastic Enclosure

Getting Started

Get a console

If you have a TS-9448, you can connect that to the 26 pin header and use the DB9 port which will by default be the console port. If you do not have a 9448, you can hold the reset button for 5 seconds (until the red led lights up) and let go to switch the console port to the onboard COM port using the standard 8n1, no flow control, 115200 baud rate.

You can also telnet to the board with the default network configuration, though this will omit the TS-BOOTROM messages.

Busybox

After the board is first booted you will be at this shell:

Finished booting in 2.65 seconds
Type 'tshelp' for help
#

See the Busybox page on configuring the default boot options, including skipping Busybox. To boot into the full debian environment now, type 'exit' at the console.

Boot Process

This board uses the TS-BOOTROM to load the OS. The SD Boot jumper, as well as the TS-9448 will decide where the system boots.

Boot Selection With TS-9448

Switch Pos.	SDBOOT Jumper	Boot Behavior
Down	Off	XNAND
None	On	Offboard SPI Flash
Up	Off	MicroSD

 Note: JP1 will cause the bootloader to only boot to SPI Flash

Boot Selection Without TS-9448

SDBOOT Jumper	Boot Behavior
Off	XNAND
On	MicroSD

Userspace Utilities

ts7500ctl

xuartctl

26 Pin Header

TS-7552/TS-7553 also includes a .1" pin spacing external header for board to board interfacing. The external interfaces uses a total of 26 pins.

Diagram

   ______________________________________ 
  | 2  4  6  8 10 12 14 16 18 20 22 24 26|
* | 1  3  5  7  9 11 13 15 17 19 21 23 25|
  \--------------------------------------/

Pinout

Pin #	Name	Function
1	JTAG_DOUT
2	JTAG_TMS	4.7k pull-up
3	GND	Ground
4	JTAG_DIN	4.7k pull-up
5	MODE2	Latched boot up mode 2, 4.7k pull-up
6	JTAG_CLK	2.2k pull-up
7	CONSOLE_TXD	Console TX, latched boot up mode 1, 4.7k pull-up
8	CONSOLE_RXD	Console RX, 4.7k pull-up
9	SPI_MISO	SPI master-in slave-out
10	3.3V	3.3V power
11	SPI_CS1	SPICS#1 output
12	SPI_MOSI	SPI master-out slave-in
13	SDA	I2C/DIO-driven by CPU, 2.2k pull-up
14	DIO_14	SPI clock output
15	SCL	I2C/DIO-driven by CPU, 2.2k pull-up
16	WD_RESET	Watchdog or system reset output
17	DIO_17	DIO,SPICS#0 output, weak FPGA pull-up
18	DIO_18	DIO,SPICS#2 output, weak FPGA pull-up
19	DIO_19	DIO, SPICS#3 output, weak FPGA pull-up, XUART#4 TX
20	DIO_20	DIO, weak FPGA pull-up, XUART#4 RX
21	DIO_21	DIO, weak FPGA pull-up, XUART#5 TX
22	DIO_22	DIO, weak FPGA pull-up, XUART#5 RX
23	DIO_23	DIO, weak FPGA pull-up, XUART#6 TX
24	DIO_24	DIO, weak FPGA pull-up, XUART#6 RX
25	DIO_25	DIO, weak FPGA pull-up, XUART#7 TX
26	DIO_26	DIO, weak FPGA pull-up, XUART#7; RX +5V

Note: As of Rev.A1 of TS-7553, Pin 26 (DIO_26) will permanently 
be +5V instead of "DIO, weak FPGA pull-up". The TS-7552 is unchanged.

None of the DIO pins are 5V tolerant. They are 3.3V LVCMOS I/O buffers with approximately 12mA current drive capability.

COM Ports

The XUART ports will be controlled with xuartctl.

XUART0

This comes from pins 3 (TX) and 2 (RX) of the DB9 port.

XUART1

This is pins 7 (TX) and 8 (RX) of the DB9 port.

Kernel

The kernel is built based off the sources provided by Cavium. See the Cavium Kernel page for compiling information.

Enclosures

The TS-7553 supports the TS-ENC820.

Related Links

FCC Advisory Statement