TS-RELAY8: Difference between revisions
No edit summary |
|||
Line 65: | Line 65: | ||
You can find the datasheet for the relays [http://www.te.com/catalog/pn/en/9-1440003-0?RQPN=PCH-105D2H%2C000 here]. | You can find the datasheet for the relays [http://www.te.com/catalog/pn/en/9-1440003-0?RQPN=PCH-105D2H%2C000 here]. | ||
The PCH-105D2H relay is normally open, closes in 10ms, and opens in 5ms. | The PCH-105D2H relay is normally open, closes in 10ms, and opens in 5ms. A very safe assumption would be that it will switch after 20ms. | ||
= IO Address Selection = | = IO Address Selection = |
Revision as of 17:02, 20 July 2011
Product Page | |
Documentation | |
---|---|
Schematic |
Overview
The TS-RELAY8 is PC/104 compatible peripheral board that provides eight independent software controlled PC board relays. This daughter board is compatible with any PC/104 main board.
Getting Started
Get the PC104 base address for 8bit access from your SBC page. You will use this as the base and add the other addresses for the registers. For example, on the TS-7800 this is 0xEE00_0000. If you have no jumpers set on the TS-Relay8, then the base address of this board will be 0xEE00_0140.
# This is only needed on the TS-7800
pc104on # part of ts7800.subr in fastboot
# Read the Identifier. This will return 0x9b
peekpoke 8 0xEE000140
# Turn off all of the relays
peekpoke 8 0xEE000142 0x00
# Turn on all of the relays
peekpoke 8 0xEE000142 0xFF
TS-Relay8 Programming
The simplest method will be to use system/popen calls in C/C++. If you need lower latency, the next best option would be to mmap the addresses and edit them there.
#include <stdio.h>
#include <sys/mman.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <stdint.h>
int main(int argc, char **argv)
{
int mem = open("/dev/mem", O_RDWR|O_SYNC);
void *base_address = mmap(0,
getpagesize(),
PROT_READ|PROT_WRITE,
MAP_SHARED,
mem,
0xEE000000);
volatile int8_t *relays;
relays = (volatile int8_t*)(base_address + 0x142);
*relays = 0x00; // All relays off
usleep(20000); // 20ms pause
*relays = 0xFF; // All relays on
usleep(20000); // 20ms pause
}
You can find the datasheet for the relays here.
The PCH-105D2H relay is normally open, closes in 10ms, and opens in 5ms. A very safe assumption would be that it will switch after 20ms.
IO Address Selection
The address selected below must not collide with other PC104 boards. If you are using others, see their page and make sure their configuration doesn't collide with this board.
JP1 | JP2 | Address |
---|---|---|
OFF | OFF | 140 |
ON | OFF | 150 |
OFF | ON | 160 |
ON | ON | 170 |
PLD Register Map
Address | Description | Access | Notes |
---|---|---|---|
Base + 0 | Board Identifier | Read Only | Relay8 is identified by 0x9b |
Base + 1 | PLD Revision | Read Only | |
Base + 2 | Relay Control | Read/Write | Control relays ON/OFF |